Recently, the national standard plan " Polyethylene Blow Molded Containers for Food Packaging " (draft for approval) has been compiled and comments are solicited until April 28, 2023. The main drafting units are Hebei Century Hengtaifu Plastic Co., Ltd., Kunshan Ziding Plastic Co., Ltd., Foshan Nanhai Xinbaode Plastic Co., Ltd., Xingping Gaoke Plastic Co., Ltd., Guangzhou Xinlian Zhitong Industrial Co., Ltd., etc.
This document specifies the requirements, test methods, inspection rules, marking, packaging, transportation and storage of polyethylene blow-molded containers for food packaging. This document is applicable to blow-molded containers with a nominal capacity of 1,000 L or less, which use polyethylene as the main raw material and are molded by hollow blow molding process and are used for food packaging.
Measured with a measuring tool with a division value not greater than 0.5 mm, the maximum dimension of the vertical projection of the sample container body is the outer diameter; the outer diameter of square and oblate square containers is calculated by the length of the diagonal. The maximum dimension of the horizontal projection of the sample is the height dimension. The difference between it and the nominal size is the size deviation, accurate to 1 mm.
For the minimum wall thickness, use instruments with a measurement accuracy of 0.02 mm, such as micrometers, vernier calipers, and non-contact instruments. Divide the container body horizontally into top, middle and bottom. For each part, take 4 stretches and measure the wall thickness at positions deviated from the dividing line (see Figure 1), and take the average value of the readings as the wall thickness of the top, middle and bottom in the report. The minimum value of all parts is the test result.
Inject water at a temperature of (20±5)°C into the sample according to the nominal capacity and tighten the cap. For containers with an inner diameter of the injection port ≤ 70 mm, lie down on a horizontal surface (the container mouth is close to the ground), and inspect after 4 hours; s/time ~ 130 s/time, reciprocate at a constant speed for 20 times before inspection, and the number of test samples is 3.
The contents of the following documents constitute the essential provisions of this document through normative references in the text. Among them, for dated references, only the version corresponding to the date applies to this document; for undated references, the latest version (including all amendments) applies to this document.
GB/T2035 - Plastic terms and their definitions
GB/T 4857.5——1992 Packaging and transportation packages, drop test method GB 5009.2—2016—National food safety standard Determination of relative density of food
GB 5009.156 National Food Safety Standard: General Rules for Pretreatment Methods for Migration Test of Food Contact Materials and Products GB/T 9174 General Technical Conditions for General Cargo Transport Packaging
GB/T 16288 Marking of plastic products
Where is the next big market for digital printing?
Digital printing of packaging has come a long way since its early days when it was primarily used to print codes and best-before dates. Today, digital printers are a major player in label and narrow w
02024-09-19114
India's tariff adjustment: MDI import tax reduced from 7.5% to 5%
Recently, India announced the adjustment of import tariffs on some commodities from July 24 and the review plan of the overall tariff structure in the next six months. MDI import duty cut: India ha
02024-09-19114
Overview of the Brazilian paper packaging and wrapping paper market: domestic sales are weak, while
Domestic packaging production in Brazil, including wrapping paper, appears to be resilient to weak domestic consumption, due to external factors and structural changes in consumer behavior. Strong gro
02024-09-19107
A look at the major reshuffle of the European paper industry from the perspective of paper mills, pa
Amid ongoing economic difficulties, the European paper industry experienced a consumption downturn in 2023 related to large-scale destocking, resulting in a decline in annual turnover for many pulp an
02024-09-19108
The revenue of the two major corrugated giants in Europe and the United States fell again in the sec
Schmurphy Kappa's leaders held their first earnings call on Tuesday since the company acquired Westrock on July 5. The uniqueness of Schmurphy Westrock cannot be overstated, and the combination of
02024-09-19110
